Model: OKU-65T
Brand: OREKU High Precision Machine
Precision: JIS Special Grade
Speed: 700 times/min
Tonnage: 65 tons
Travel: 30mm
Plug terminal high speed punching machine standard accessory:
1. Electric mold height adjustment
2. Module height display accuracy of 0.01
3. Inching function, single action function, linkage function
4. The linkage has 0 ° and 90 ° positioning parking functions
5. Sliding pad
6. Six groups of batch control
7. Two sets of inclined groove control
8. Hydraulic locking mold
9. Hydraulic engine base screw pile
10. Hydraulic mold lifter and mold arm
11. Lubricating cooling circulation machine
12. Independent electrical control box
13. Host forward and reverse device
14. Separate brake clutch
15. Spring type shock-absorbing foot pads
16. Work lights
17. Maintenance tools and toolboxes
Plug terminal 65T precision high-speed automatic punching machine punching machines:
1. Gear feeder (width selection: 150/200/300/400)
2. NC servo feeder
3. Double head material rack (hydraulic expansion/manual expansion) (width selection: 200/300/400)
4. S-type leveling machine
5. Tonnage detector
6. Bottom dead center monitor
7. Electric control box air conditioning
8. Variable frequency permanent magnet motor
Plug terminal 65T precision high speed automatic punching machine optional accessories:
Nominal force: 65T
Ability occurrence point: 2.0mm
Stroke: 30mm
Strokes: 150-700 s.p.m
Workbench area: 950 x 650 mm
Cutting hole: 700 × 125mm
Sliding seat area: 950 x 420mm
Mold height adjustment stroke: 300-350 mm
Module height adjustment motor: 0.4kw
Main motor: 19kw
External dimensions: 2010 x 1660 x 2950 mm
Total weight: 12.5 tons
Precision high-speed automatic punching machine structure
Precision high-speed automatic punching machine stamping products
Maintenance of precision high-speed automatic punching machine:
1. Regularly keep the center pillar and slider guide pillar clean, and ensure that the bottom plate of the mold is free of dirt during mold installation to ensure the cleanliness of the platform and avoid scratches. 2. When using a new machine for one month, add butter to the flywheel (including the feeder). If there is no oil added for a long time, it will cause internal wear of the flywheel and affect the performance of the machine tool. In the future, it is also necessary to add butter that can withstand high temperatures above 150 ℃ for each maintenance
3. Replacement of machine circulating oil: The new machine should be replaced once within a month, and then every six months to ensure the normal operation and precision of the machine tool (32 # mechanical oil or Mobil 1405 #)
Usage of precision high-speed automatic punching machine:
1. Before starting up, the speed control potentiometer (W) set on the control panel should be adjusted to the lowest point (O point) position.
2. After the main power switch (DK) is turned on, the power indicator light should be on, and the phase sequence indicator light should also be on. Otherwise, check if the phase sequence is correct.
3. Turn on the control circuit with the key switch and disconnect the phase. The three indicator lights should light up simultaneously, otherwise they should be checked and the fault should be eliminated.
4. Adjust the "speed regulation" potentiometer clockwise, the main motor drives the flywheel to start, and the speed should be stable without any oscillation or impact.
5. During the process of connecting the main clutch, both hands should operate simultaneously. During the formal stamping process, the external control button switch should be turned on and the machine adjustment button switch should be in a reset state before it can officially work, otherwise the feeding switch and mold fault signal will lose control.
6. During the formal punching process, due to the variation of the static error rate of the main motor with different loads, an electromagnetic counter set on the control board can be used to correct the speed when punching different parts.
